THE USE OF CAD PROGRAMS FOR DESIGNING SPECIAL INSTRUMENTATION IN ADHESIVE TECHNOLOGIES
Jacek Tomasz Ogrodniczek
eggy94@wp.plLublin University of Technology, Faculty of Mechanical Engineering, Department of Production Engineering, 36 Nadbystrzycka Str., 20-618 Lublin (Poland)
Adrian Pyda
Lublin University of Technology, Faculty of Mechanical Engineering, Department of Production Engineering, 36 Nadbystrzycka Str., 20-618 Lublin (Poland)
Mariusz Kłonica
Lublin University of Technology, Faculty of Mechanical Engineering, Department of Production Engineering, 36 Nadbystrzycka Str., 20-618 Lublin (Poland)
https://orcid.org/0000-0001-6149-1710
Abstract
The role of adhesive technology in industry has increased significantly in recent times. The need to transfer evergreater stresses while reducing the mass of devices causes difficulties in engineering. The use of dissimilar
materials prioritise this technology. Special equipment is required to ensure the right technological conditions.
CAD software facilitates the creation of a virtual design to meet the formulated requirements. This article
presents the method of designing the instrumentation allowing to conduct the study of adhesives cured by UV
rays.
Keywords:
CAD programs, UV, adhesive joints, cohesionReferences
A. Rudawska, Wybrane zagadnienia konstruowania połączeń adhezyjnych jednorodnych i hybrydowych. Lublin: Politechnika Lubelska, 2013.
Google Scholar
Z. Mirski and T. Piwowarczyk, „Podstawy klejenia, kleje i ich właściwości”, Przegląd spawalnictwa, vol. 8, pp. 12-21, 2008.
Google Scholar
J. Szabelski, Badania wpływu obróbki cieplnej doczołowych połączeń klejowych na ich wytrzymałość statyczną. Lublin: Politechnika Lubelska, 2014.
Google Scholar
W. Wielgołaski, Poradnik serwisowy, vol. 3, pp. 238 – 241, 2002.
Google Scholar
M. Kłonica, Badania stanu energetycznego warstwy wierzchniej wybranych materiałów konstrukcyjnych po ozonowaniu. Lublin: Politechnika Lubelska, 2014.
Google Scholar
M. Kłonica and J. Kuczmaszewski, “Determining the value of surface free energy on the basis of the contact angle”, Advances in Science and Technology Research Journal, vol. 11, no. 1, pp. 66-74, 2017.
Google Scholar
J. Kuczmaszewski, Fundamentals of metal-metal adhesive joint design. Lublin: Politechnika Lubelska, 2006. http://www.loctite.pl/produkty-wedlug-zastosowania-6442.htm.
Google Scholar
A. Rudawska, Oprzyrządowanie w technologii klejenia. Lublin, Politechnika Lubelska, 2013.
Google Scholar
M. Kwiatkowski, M. Kłonica, J. Kuczmaszewski and S. Satoh, “Comparative analysis of energetic properties of Ti6AI4V titanium and EN-AW-2017A(PA6) aluminum alloy surface layers for an adhesive bonding application”, Ozone-Science & Engineering, vol. 35, no. 3, pp. 220-228, 2013.
Google Scholar
M. Sydor, Wprowadzenie do CAD. Podstawy Komputerowo Wspomaganego Projektowania. Wydawnictwo Naukowe PWN, 2009.
Google Scholar
C. Burton and W. Marosz, “The Construction and Uses of CATIA, a Computerized Mathematics Testbank”, The Two-Year College Mathematics Journal, vol. 8, no. 4, pp. 212-216, 1977.
Google Scholar
https://www.3ds.com/products-services/catia/.
Google Scholar
https://camdivision.pl/pl/produkty/nx-cad.
Google Scholar
https://www.plm.automation.siemens.com/en_pl/Images/10_powodow_tcm801-79972.pdf.
Google Scholar
Siemens PLMS, „10 powodów, dla których warto wybrać Solid Edge”, Mechanik vol. 3, 2009. http://barwyszkla.pl/klejenie-szkla-uv/
Google Scholar
Authors
Jacek Tomasz Ogrodniczekeggy94@wp.pl
Lublin University of Technology, Faculty of Mechanical Engineering, Department of Production Engineering, 36 Nadbystrzycka Str., 20-618 Lublin Poland
Authors
Adrian PydaLublin University of Technology, Faculty of Mechanical Engineering, Department of Production Engineering, 36 Nadbystrzycka Str., 20-618 Lublin Poland
Authors
Mariusz KłonicaLublin University of Technology, Faculty of Mechanical Engineering, Department of Production Engineering, 36 Nadbystrzycka Str., 20-618 Lublin Poland
https://orcid.org/0000-0001-6149-1710
Statistics
Abstract views: 201PDF downloads: 122
License
This work is licensed under a Creative Commons Attribution 4.0 International License.
All articles published in this journal are open access and distributed under the terms of the Creative Commons Attribution 4.0 International License.
