SIMULATION OF TORQUE VARIATIONS IN A DIESEL ENGINE FOR LIGHT HELICOPTERS USING PI CONTROL ALGORITHMS
Paweł MAGRYTA
p.magryta@pollub.plLublin University of Technology (Poland)
https://orcid.org/0000-0002-9654-2909
Grzegorz BARAŃSKI
Lublin University of Technology (Poland)
https://orcid.org/0000-0003-2596-3148
Abstract
This article presents the results of simulation research of a diesel engine for a light helicopter. The simulations were performed using the 1D software AVL Boost RT. The engine model includes elements such as cylinders, turbine, compressor, inlet and outlet valves, ambient environment definition, and fuel injection control strategy. The simulations aimed to evaluate the engine's response to step changes in the main rotor load, both increasing and decreasing power demands. Parameters analyzed included power deviation, torque, engine rotational speed, and stabilization time of the main rotor rotational speed. All tests were conducted using a single set of PI controller settings. The results demonstrate that these parameters are dependent on the magnitude of the step change in the main rotor load demand. The study compares the maximum engine rotational speed deviation from the nominal value for both increasing and decreasing main rotor load demands. The findings indicate that using PI regulator to control rotational speed in the diesel engine in a light helicopter significantly depends on the change in the load torque on the rotor.
Keywords:
Diesel engine, PI control, algorithm, speed regulation, helicopter propulsionReferences
Ang, K. H., Chong, G., & Li, Y. (2005). PID control system analysis and design. IEEE Transactions on Control Systems Technology, 13(4). 559-576. https://doi.org/10.1109/TCST.2005.847331
Google Scholar
Åström, K. J., & Murray, R. M. (2008). Feedback Systems: An Introduction for Scientists and Engineers. Princeton University Press.
Google Scholar
Banaszuk, A., Ariyur, K. B., Krstić, M., & Jacobson, C. A. (2004). An adaptive algorithm for control of combustion instability. Automatica, 40(11), 1965-1972. https://doi.org/10.1016/j.automatica.2004.06.008
Google Scholar
Beller, G., Árpád, I., Kiss, J. T., & Kocsis, D. (2021). AVL Boost: a powerful tool for research and education. Journal of Physics Conference Series, 1935, 012015. https://doi.org/10.1088/1742-6596/1935/1/012015
Google Scholar
Czyż, Z., Jakubczak, P., Podolak, P., Skiba, K., Karpiński, P., Droździel-Jurkiewicz, M., & Wendeker, M. (2023). Deformation measurement system for UAV components to improve their safe operation. Eksploatacja i Niezawodność – Maintenance and Reliability, 25(4), 172358. https://doi.org/10.17531/ein/172358
Google Scholar
Czyż, Z., Łusiak, T., Czyż , D., & Kasperek, D. (2016). Analysis of the pre-rotation engine loads in the autogyro. Advances in Science and Technology. Research Journal, 10(31), 169-176. https://doi.org/10.12913/22998624/64015
Google Scholar
Dudnika, V., & Gaponova, V. (2022). Correction system of the main rotor angular speed for helicopters of little weight categories. Transportation Research Procedia, 63, 187-194. https://doi.org/10.1016/j.trpro.2022.06.004
Google Scholar
Heywood, J. B. (1988). Internal Combustion Engine Fundamentals. McGraw-Hill.
Google Scholar
Hlinka, J., Kostial, R., & Horpatzka M. (2021). Application of enhanced methods for safety assessment of FADEC. Maintenance and Reliability, 23(1), 63-73. https://doi.org/10.17531/ein.2021.1.7
Google Scholar
Łusiak, T., & Grudzień, A. (2013). Rotor turbulence influence on helicopter flights in high urban built-up area. Advances in Science and Technology Research Journal, 7(17), 47-50. https://doi.org/10.5604/20804075.1036997
Google Scholar
Magryta, P. (2021). 1D modelling and PID control of helicopter diesel engine rotational speed in torque changes. Journal of Physics: Conference Series, 2130, 012007. https://10.1088/1742-6596/2130/1/012007
Google Scholar
Magryta, P., & Majczak, A. (2012). Diesel engine applicability in a light helicopter. Autobusy: technika, eksploatacja, systemy transportowe, 13(4), 98-103.
Google Scholar
Mueller, T. J. (2002). Introduction to the design of fixed-wing micro air vehicles: Including three case studies. AIAA Education Series.
Google Scholar
Niederliński, A., Mościński, J., & Ogonowski, Z. (1995). Regulacja adaptacyjna. Wydawnictwo Naukowe PWN.
Google Scholar
Omran, I., Mostafa, A., Seddik, A., Ali, M., Hussein, M., Ahmed, Y., Aly, Y., & Abdelwahab, M. (2024). Deep reinforcement learning implementation on IC engine idle speed control. Ain Shams Engineering Journal, 15(5): 102670. https://doi.org/10.1016/j.asej.2024.102670
Google Scholar
Pietrykowski, K., Magryta, P., Wendeker, M., & Czyż, Z. (2014). Simulation studies of the helicopter diesel engine exploitation. Logistyka, 2014(3), 5111-5117.
Google Scholar
Przystupa, K. (2018). Tuning of PID controllers - Approximate methods. Advances in Science and Technology Research Journal, 12(4), 56-64. https://doi.org/10.12913/22998624/99987
Google Scholar
Stone, R. (1992). Introduction to Internal Combustion Engines. Palgrave Macmillan.
Google Scholar
Wang, Y., Pan, M., Zhou, W., & Huang, J. (2023a). Direct thrust control for variable cycle engine based on fractional order PID-nonlinear model predictive control under off-nominal operation conditions. Aerospace Science and Technology, 143, 108726. https://doi.org/10.1016/j.ast.2023.108726
Google Scholar
Wang, Z., Du, J., & Guo, H. (2023b) A study on optimal rotor speed control method for helicopter power system considering the influence of infrared suppressors. International Journal of Turbo & Jet-Engines, 41(3), 519-528. https://doi.org/10.1515/tjj-2023-0048
Google Scholar
Wendeker, M., Siadkowska, K., Magryta, P., Czyż, Z., & Skiba, K. (2014). Optimal diesel engine technology analysis matching the platform of the helicopter. World Academy of Science, Engineering and Technology International Journal of Mechanical, Industrial Science and Engineering, 8(5). https://doi.org/10.5281/zenodo.1092291
Google Scholar
Zang, H., Changkai, Y., & Guoqiang, C. (2013). Variable rotor speed control for an integrated helicopter/engine system. Proceedings of the Institution of Mechanical Engineers Part G Journal of Aerospace Engineering, 228(3), 323-341. https://doi.org/10.1177/0954410013485010
Google Scholar
Authors
Paweł MAGRYTAp.magryta@pollub.pl
Lublin University of Technology Poland
https://orcid.org/0000-0002-9654-2909
Authors
Grzegorz BARAŃSKILublin University of Technology Poland
https://orcid.org/0000-0003-2596-3148
Statistics
Abstract views: 197PDF downloads: 55
License
This work is licensed under a Creative Commons Attribution 4.0 International License.
All articles published in Applied Computer Science are open-access and distributed under the terms of the Creative Commons Attribution 4.0 International License.
Most read articles by the same author(s)
- Paweł MAGRYTA, AERODYNAMIC RESEARCH OF THE OVERPRESSURE DEVICE FOR INDIVIDUAL TRANSPORT , Applied Computer Science: Vol. 13 No. 1 (2017)
Similar Articles
- Jarosław WIKAREK, Paweł SITEK, Mieczysław JAGODZIŃSKI, A DECLARATIVE APPROACH TO SHOP ORDERS OPTIMIZATION , Applied Computer Science: Vol. 15 No. 4 (2019)
- Zbigniew CZYŻ, Paweł KARPIŃSKI, Tacetdin SEVDIM, NUMERICAL ANALYSIS OF THE DRAG COEFFICIENT OF A MOTORCYCLE HELMET , Applied Computer Science: Vol. 14 No. 1 (2018)
- Mario BELLO, Alejandra LUNA, Edmondo BONILLA, Crispin HERNANDEZ, Blanca PEDROZA, Alberto PORTILLA, A NOVEL PROFILE’S SELECTION ALGORITHM USING AI , Applied Computer Science: Vol. 16 No. 1 (2020)
- Krzysztof OSTROWSKI, AN EFFECTIVE METAHEURISTIC FOR TOURIST TRIP PLANNING IN PUBLIC TRANSPORT NETWORKS , Applied Computer Science: Vol. 14 No. 2 (2018)
- Damian GIEBAS, Rafał WOJSZCZYK, GRAPHICAL REPRESENTATIONS OF MULTITHREADED APPLICATIONS , Applied Computer Science: Vol. 14 No. 2 (2018)
- Moon-gee CHOI, USE OF SERIOUS GAMES FOR THE ASSESSMENT OF MILD COGNITIVE IMPAIRMENT IN THE ELDERLY , Applied Computer Science: Vol. 18 No. 2 (2022)
- Marcin MACIEJEWSKI, Barbara MACIEJEWSKA, Robert KARPIŃSKI, Przemysław KRAKOWSKI, ELECTROCARDIOGRAM GENERATION SOFTWARE FOR TESTING OF PARAMETER EXTRACTION ALGORITHMS , Applied Computer Science: Vol. 16 No. 4 (2020)
- Damian KOLNY, Dorota WIĘCEK, Paweł ZIOBRO, Martin KRAJČOVIČ, APPLICATION OF A COMPUTER TOOL MONITORING SYSTEM IN CNC MACHINING CENTRES , Applied Computer Science: Vol. 13 No. 4 (2017)
- Maria TOMASIKOVA, Frantisek BRUMERČÍK, Aleksander NIEOCZYM, DESIGN AND DYNAMICS MODELING FOR ELECTRIC VEHICLE , Applied Computer Science: Vol. 13 No. 3 (2017)
- Muaayed F. AL-RAWI, CONVENTIONAL ENERGY EFFICIENT ROUTING PROTOCOLS IN WIRELESS SENSOR NETWORKS , Applied Computer Science: Vol. 16 No. 3 (2020)
<< < 1 2 3 4 5 6 7 8 9 10 > >>
You may also start an advanced similarity search for this article.
