COMPUTER SUPPORT OF ERGONOMIC ANALYSIS OF WORKING CONDITIONS AT WORKSTATIONS
Damian KOLNY
dkolny@ath.bielsko.pl University of Bielsko-Biala, Faculty of Mechanical Engineering and Computer Science, Willowa 2, 43-309 Bielsko-Biała (Poland)
Dawid KURCZYK
University of Bielsko-Biala, Faculty of Mechanical Engineering and Computer Science, Willowa 2, 43-309 Bielsko-Biała (Poland)
Józef MATUSZEK
University of Bielsko-Biala, Faculty of Mechanical Engineering and Computer Science, Willowa 2, 43-309 Bielsko-Biała (Poland)
Abstract
The article shows issues of using computer-aided technologies for ergonomic analysis at worksplaces using a dedicated tool in the Delmia environment. The scope of the ergonomic evaluation has been limited to the analysis of RULA and NIOSH, the data needed for it was gathered on the basis of observation, interview and task analysis. The results of the research showed the strenous nature of the work, therefore improvements within undertaken workplace area were proposed and re-analyzed. The obtained results proved reduction of strenousness, which was the basis for the practical implementation of the proposed changes.
Keywords:
work ergonomics, modeling and simulationReferences
Genaidy, A. M., Al.-Shed, A. A., & Karwowski W. (1994). Postural stress analysis in industry. Applied Ergonomics, 25(2), 77–87.
DOI: https://doi.org/10.1016/0003-6870(94)90068-X
Google Scholar
Klembalska, K. (2006). Modelowanie bezpieczeństwa maszyny na etapie koncepcji jako narzędzie kształtowania ergonomii i bezpieczeństwa pracy. Journal of Research and Applications in Agricultural Engineering, 51(4), 21–29.
Google Scholar
Lasota, A. M., & Hankiewicz, K. (2015). Ergonomiczna ocena pozycji przy pracy w procesie cięcia i pakowania materiałów termoizolacyjnych. Logistyka, 5, 1059–1065.
Google Scholar
Marconi, M., Germani, M., Favi, C., & Raffaeli, R. (2018). CAD feature recognition as a means to prevent ergonomics issues during manual assembly tasks. Computer-Aided Design and Applications. https://doi.org/10.1080/16864360.2018.1441240
DOI: https://doi.org/10.14733/cadconfP.2017.400-404
Google Scholar
McAtamney, L., & Corlett, E. N. (1993). RULA: a survey method for the investigation of workrelated upper limb disorders. Applied Ergonomics, 24(2), 91–99.
DOI: https://doi.org/10.1016/0003-6870(93)90080-S
Google Scholar
Muszyński, Z. (2016). Rozwój ergonomii w Polsce i na świecie. Zeszyty Naukowe Małopolskiej Wyższej Szkoły Ekonomicznej w Tarnowie, 29(1), 87–100.
Google Scholar
Nowacka, W. Ł. (2010). Ergonomia i ergonomiczne projektowanie stanowisk pracy. Materiały dydaktyczne dla słuchaczy Studiów Podyplomowych „Bezpieczeństwo i ochrona człowieka w środowisku pracy i ergonomia”. Warszawa: Wydawnictwo Politechniki Warszawskiej.
Google Scholar
Slamková, E., Dulina, L., & Tabaková, M. (2010). Ergonómiwa v priemysle. Žilina: GEORG knihárstvo, tlačiareň.
Google Scholar
Zielińska, A., & Kurczyk, D. (2011). Wybrane narzędzie ergonomiczne w środowisku Delmia, Modele inżynierii teleinformatyki (Wybrane zastosowania) 6 (pp. 95–106). Koszalin: Wydawnictwo Uczelniane Politechniki Koszalińskiej.
Google Scholar
Authors
Damian KOLNYdkolny@ath.bielsko.pl
University of Bielsko-Biala, Faculty of Mechanical Engineering and Computer Science, Willowa 2, 43-309 Bielsko-Biała Poland
Authors
Dawid KURCZYKUniversity of Bielsko-Biala, Faculty of Mechanical Engineering and Computer Science, Willowa 2, 43-309 Bielsko-Biała Poland
Authors
Józef MATUSZEKUniversity of Bielsko-Biala, Faculty of Mechanical Engineering and Computer Science, Willowa 2, 43-309 Bielsko-Biała Poland
Statistics
Abstract views: 168PDF downloads: 31
License
This work is licensed under a Creative Commons Attribution 4.0 International License.
All articles published in Applied Computer Science are open-access and distributed under the terms of the Creative Commons Attribution 4.0 International License.
Most read articles by the same author(s)
- Damian KOLNY, Dorota WIĘCEK, Paweł ZIOBRO, Martin KRAJČOVIČ, APPLICATION OF A COMPUTER TOOL MONITORING SYSTEM IN CNC MACHINING CENTRES , Applied Computer Science: Vol. 13 No. 4 (2017)
- Józef MATUSZEK, Tomasz SENETA, Aleksander MOCZAŁA, FUZZY ASSESSMENT OF MANUFACTURABILITY DESIGN FOR MACHINING , Applied Computer Science: Vol. 15 No. 3 (2019)
Similar Articles
- Eduardo Sánchez-García, Javier Martínez-Falcó, Bartolomé Marco-Lajara, Jolanta Słoniec, ANALYZING THE ROLE OF COMPUTER SCIENCE IN SHAPING MODERN ECONOMIC AND MANAGEMENT PRACTICES. BIBLIOMETRIC ANALYSIS , Applied Computer Science: Vol. 20 No. 1 (2024)
- Mateusz Sawa, Mirosław Szala, Weronika Henzler, INNOVATIVE DEVICE FOR TENSILE STRENGTH TESTING OF WELDED JOINTS: 3D MODELLING, FEM SIMULATION AND EXPERIMENTAL VALIDATION OF TEST RIG – A CASE STUDY , Applied Computer Science: Vol. 17 No. 3 (2021)
- Dias Satria, PREDICTING BANKING STOCK PRICES USING RNN, LSTM, AND GRU APPROACH , Applied Computer Science: Vol. 19 No. 1 (2023)
- Elvis COUTIÑO-MORENO, Quirino ESTRADA, Daniel MALDONADO-ONOFRE, Alejandro RODRIGUEZ-MENDEZ, Julio GOMEZ-GIRON, RESOLUTION IN THE 3D MODELING OF OBJECTS FOR ADDITIVE MANUFACTURING AND REVERSE ENGINEERING – SHUTTER EFFECT , Applied Computer Science: Vol. 17 No. 1 (2021)
- Mariano LARIOS, Perfecto M. QUINTERO-FLORES , Mario ANZURES-GARCÍA , Miguel CAMACHO-HERNANDEZ , APPLICATION OF THE REAL-TIME FAN SCHEDULING IN THE EXPLORATION-EXPLOITATION TO OPTIMIZE MINIMUM FUNCTIONS OBJECTIVES , Applied Computer Science: Vol. 19 No. 2 (2023)
- Kadeejah ABDULSALAM, John ADEBISI, Victor DUROJAIYE, IMPLEMENTATION OF A HARDWARE TROJAN CHIP DETECTOR MODEL USING ARDUINO MICROCONTROLLER , Applied Computer Science: Vol. 17 No. 4 (2021)
- Sylwester KORGA, Marcin BARSZCZ, Krzysztof DZIEDZIC, DEVELOPMENT OF SOFTWARE FOR IDENTIFICATION OF FILAMENTS USED IN 3D PRINTING TECHNOLOGY , Applied Computer Science: Vol. 15 No. 1 (2019)
- Wiesław FRĄCZ, Grzegorz JANOWSKI, Grażyna RYZIŃSKA, THE POSSIBILITY OF USING WOOD FIBER MATS IN PRODUCTS MANUFACTURING MADE OF POLYMER COMPOSITES BASED ON NUMERICAL SIMULATIONS , Applied Computer Science: Vol. 13 No. 4 (2017)
- Paweł MAGRYTA, Grzegorz BARAŃSKI, SIMULATION OF TORQUE VARIATIONS IN A DIESEL ENGINE FOR LIGHT HELICOPTERS USING PI CONTROL ALGORITHMS , Applied Computer Science: Vol. 20 No. 3 (2024)
- Konrad PIETRYKOWSKI, Paweł KARPIŃSKI, SIMULATION STUDY OF HYDRODYNAMIC CAVITATION IN THE ORIFICE FLOW , Applied Computer Science: Vol. 18 No. 3 (2022)
You may also start an advanced similarity search for this article.
